Check the network connections between the PC and the device you are pinging. 9 and is configured with Profinet. Issue: I can. The computer issuing the PING command cannot communicate with the device a...
Hi All, I am facing an issue with a switch. Please refer my below sample diagrams to understand the network setup. Here i am unable
I can now ping the IP from all of the switches, no problem, also not when I log on to the core switch in the same VLAN
I''ve got two physical computers which are connected to the same unmanaged switch. Said switch is connected to a
The switch has a layer 3 port whose IP is 172.30.0.2. I can ping my PC from the switch but when I introduce the
Once all the changes had been saved, the switch & pc ip addresses were now able to be pinged. However, back in
The Switch has several other VLANs for other IT infrastructure. Issue: I can successfully ping and scan the Profinet
Hi, I''ve got this one Catalyst switch on my network that I am not able to ping, except in rare situations (like earlier
Hi all, I have 3 cisco cbs-350''s that are all connected to each other and can all be pinged and accessed when on the
While the poe works great, the machines connected to the switch can only communicate among each other and
If a switch is directly connected to another network device, ensure that the connected ports have the same type and VLAN
Hello, Dears I have set-up a small network based on two cisco 2960xr switches with IP Lite
I just can''t see what I need to do to get a host connected to the switch to talk to the internet. The switch itself can, but a device
Having issues pinging a device through the LAN port to a PC via Ethernet. The device is not directly, connected to
When my PC is connected to the modem via LAN cable, I cannot ping it from my laptop when the laptop is also
I can ping from Network A to both interfaces on Router 1 (192.168.10.1, 192.168.30.1) Even though Network B has been automatically
Hello tsterling001, I spun up a test 2-node simulation, and used the default ANK settings to build initial configurations. After bootup, I
Am I reading it correctly that you can PING/scan the X.21/X.22 devices, but not the X.9 PLC, when all are connected
Switch A and switch B cannot ping each other, and the OSPF neighbor status on switch A is Exchange. After switch
09-27-2023 11:32 PM - last edited on 09-27-2023 11:55 PM by shaiksh hi i configure on my lab, two routers R1 and R2 directly
I''m currently training for my CCNA and am using Packet Tracer to build simple networks. I ran into an issue where I was unable to
Solved: hi i configure on my lab, two routers R1 and R2 directly connected and R1 is Connected RED network, and
Hello Cisco community, i''ve got a weird problem. I have a server "A" connected to Gig2/0/18 as an access port
Devices connected to switch cannot ping the internet, but the switch can Hi! I have an annoying issue, and I think I am missing
Troubleshooting industrial network communication issues should start with network diagnostics, not PLC code or sensor checks,
I can ping the two PLC devices (192.168.101.21, 192.168.101.22) that use Modbus over TCP/IP. However, when the
I can communicate to all of the plcs remotely through rslinx but can''t ping to any of them unless I connect directly to
I configured another interface for that and I connected the new host. These 2 hosts, same VLAN, can ping each other
Can you ping with it directly connected to your laptop? Test the cable directly, just because lights are on doesn''t mean it''s working.
Check the network connections between the PC and the device you are pinging. Verify that the device being pinged
A PC and an industrial control device are connected to the S5735S-H24S4XC-A switch. The industrial control device uses a 100M
I''m having difficulty seeing devices at either end of a new VLAN, and I cannot figure out why. What is puzzling is that
Contact us today for product inquiries, custom kits, or integration support